manualshive.com logo in svg

Epson Stylus 1500, Service Manual

Share
Download
Epson Stylus 1500 Service Manual Download Page 67

Normal Dot / EPSON Micro Dot Printing Modes

The Stylus 1500 uses two ink eject modes (normal dot and EPSON Micro Dot) for monochrome ink
printing.  Normal dot printing mode uses a larger dot size than Micro Dot printing, so the space
between dots is narrower.

In EPSON Micro Dot Printing Mode, the print dot is smaller.  This mode is useful for a larger
graded representation and for preventing white banding.  Micro Dot mode  can be used with
EPSON’s premium ink jet paper or with transparencies, using the appropriate paper settings.  This
mode can also be selected for printing on normal paper in super fine (720 dpi) quality.

COM

BHLAT

BHSO

BHCLK

#1

#64

BH1/2C
BH1/2D

NCHG

VH

Figure 2-30. EPSON Micro Dot Printing Driver Waveform

Operating Principles

2-26

Rev. A

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands