Epson Stylus 1500 Service Manual Download Page 24

Page: 24 / 185

Panel Functions at Power On

The table below describes functions performed when you hold down the indicated buttons while
turning on the printer.

Table 1-6. Panel Functions at Power On

Button

Function at Printer Power On

Alt

Starts demonstration printing.

Economy/Condensed

Enters default setting mode.

Pause

Enters print adjustment mode.

Load/Eject

Starts LQ mode self-test printing.

LF/FF

Starts Draft mode self-test printing.

Alt

Pause

Enters ink smudge prevention mode.

LF/FF + Load/Eject

Enters hex dump mode.

Alt

Economy/Condensed

LF/FF

+ Pause

Enters reset mode for the EEPROM and Timer IC
(for factory and service use only).

Notes:

1. The + sign means to press one button while holding down the other button(s).
2. The EEPROM and Timer IC must be reset only by qualified service personnel.

Printer Features

EPSON Stylus 1500 Service Manual

1-17

Summary of Contents for Stylus 1500


























































































































































































Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands

Epson Stylus 1500, Service Manual

Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands