manualshive.com logo in svg

Epson Stylus 1500, Service Manual

Share
Download
Epson Stylus 1500 Service Manual Download Page 22

OPERATIONS

This section describes the controls, settings, and adjustments used to operate the Stylus 1500.

Control Panel

The control panel for this printer is in the center of the upper case.  The panel has 1 lock-type and 6
non-lock-type pushbuttons, and 10 LED indicators for easy operation of the various print functions.

Buttons

Power

This button turns the printer on or off.

ATTENTION

The power button controls the secondary power supply circuit.  Therefore, the primary
circuit remains active after power off.  Do not connect the interface cable (even if printer
power is off) while the AC cord is connected. Otherwise, the circuit board or interface may
be damaged.

Pause

This button alternates between printing and non-printing states when there is data in the print
buffer.  In the pause state, printing stops but communication with the I/F does not stop.  Therefore,
even in the pause state, the printer receives data from the host until the input data buffer is full.

❏

Pressing the 

Pause

 button while holding down the 

Alt

 button resets the printer.

Alt

This button is usually used with another button.

❏

Holding down 

Alt

 for 3 seconds moves the printer carriage to the ink cartridge 

installation position.  Pressing 

Alt

 again returns the carriage to the home position.

LF/FF

This button feeds one line or a page.

❏

Pressing 

LF/FF

 while holding down 

Alt

 starts the black printhead cleaning cycle.

Economy/Condensed

This button selects economy or condensed printing mode.

Figure 1-5. Control Panel Appearance

Printer Features

EPSON Stylus 1500 Service Manual

1-15

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands