manualshive.com logo in svg

Epson Stylus 1500, Service Manual

Share
Download
Epson Stylus 1500 Service Manual Download Page 28

Table 1-9.  Print Direction Mode Characteristics

Item

Monochrome Printing

Color Printing

Auto

❒

Throughput and quality is better.

❒

Throughput is better.

❒

Color quality with special paper is 

 worse. 

(Color 

correction 

depends

  on the printing direction.)

Bi-D

❒

Throughput is best.

❒

Print quality may be down.

❒

Throughput is better.

❒

Color quality with special paper is 

   worse. (Color correction depends
  on the printing direction.)

Uni-D

❒

Throughput is worse.

❒

Print quality is better.

❒

Throughput is worse.

❒

Color quality is best.

Table 1-10.  Printing Direction and ESC U Command

Default Setting

Mode

Auto

Bi-D

Uni-D

ESC U

0

ESC U

1

None

ESC U

0

ESC U

1

None

ESC U

0

ESC U

1

None

Character  mode
(for DOS)

Auto

Auto

Auto

Bi-D

Uni-D

Bi-D

Uni-D

Uni-D

Uni-D

Raster graphics
mode
(for Windows)

Bi-D

Uni-D

Auto

Bi-D

Uni-D

Bi-D

Bi-D

Uni-D

Uni-D

Note:

The printing direction is controlled by a driver in the Windows environment.

Printer Features

EPSON Stylus 1500 Service Manual

1-21

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands