Epson Stylus 1500 Service Manual Download Page 81

Page: 81 / 185

Power Supply Unit (C172 PSB/PSE Board) Removal

Remove the upper housing. (See page 3-7.)

Remove the printer mechanism. (See page 3-9.)

Disconnect the power cable from connector CN1 on the C172 PSB/PSE board and the harness
from connector CN2 from the main controller board.

Remove 4 (CBP 3

× 12

) screws securing the power supply unit to the lower housing; then

remove the power supply unit.

WARNING

Because the power switch is located in the secondary side of C172 PSB/PSE, the primary
side remains hot, even if power is off. Therefore, disconnect the power cable from the AC
inlet.

C1 72 PSB/PSE

CBP 3 x 12

C N 1

C N 2

Lower Hou sin g

Figure 3-7. Removing the Power Supply Unit

Disassembly and Assembly

3-12

EPSON Stylus 1500 Service Manual

Summary of Contents for Stylus 1500


























































































































































































Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands

Epson Stylus 1500, Service Manual

Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands