Epson Stylus 1500 Service Manual Download Page 48 | Manualshive

Page: 48 / 185

background image

Paper Feed Mechanism

This printer’s paper feed mechanism consists of the built-in auto sheet feeder (ASF), push tractor,
paper feed (PF) motor, front/rear paper end (PE) sensors, PF roller, eject roller unit, and disengage
mechanism. The PF motor is a 4-phase, 48-pole, PM-type stepping motor that directly drives the
paper feed mechanism (for paper advancing and paper pickup).  This motor also drives the pump
mechanism, but only when the printer is in the cleaning state.  The paper feed mechanism is driven
using a 1-2 phase drive method, except in the paper feed drive sequence (W1-2 phase).  The paper
feed mechanism is illustrated in Figure 2-6.

The disengage mechanism switches PF motor torque between the PF drive and pump drive via the
carriage unit stop positions.  PF motor torque is transmitted to the PF roller via the PF motor
pinion, disengage mechanism, and gear  train.  The torque is then separated for each of the two
directions of the PF roller. One direction of torque transmission is used to drive the paper-ejecting
mechanism via the gear train of the upper paper guide assembly.  The other direction is used to
drive the push tractor or ASF mechanism.

Table 2-3. Paper Feed Motor Specifications

Item

Description

Motor type

4-phase, 96-pole, HB-type

Drive voltage

+42 VDC

±

5%

Coil resistance

10

Ω ±

10%

Drive frequency

300 - 2160 Hz

Excitation mode

❑

Constant current bipolar drive

❑

Paper feed / pump drive: 2-2 phase, W1-2 phase

Minimum step

1/720" (2-2 phase)

Table 2-4. Drive Terms (Paper Feed Mechanism)

Mode

Frequency

(Hz)

Current Value (A / Phase)

Acceleration

W1-2 / 2-2

Phase

Constant

Deceleration

W1-2 / 2-2

Phase

Rush

(before

/ after)

Paper loading (ASF)

2160

0.9 / 0.9

0.9

0.75 / 0.75

0.6 / 0.6

Paper feed

2160

0.9 / 0.9

0.9

0.75 / 0.75

0.6 / 0.6

Pump drive

700

— / 0.9

0.9

0.9 / —

0.75 / 0.75

Pump drive
(lower speed)

300

— / —

0.9

— / —

0.75 / 0.75

Note:

Hold current is 0.6 A.

Operating Principles

EPSON Stylus 1500 Service Manual

2-7

«
...
46
47
48
49
50
...
»

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Related manuals for Stylus 1500

Brand: Xerox Pages: 73

Brand: Xerox Pages: 2

Brand: Panasonic Pages: 102

Brand: ABLE Pages: 26

Brand: SPRT Pages: 28

Brand: Xerox Pages: 23

Brand: IBM Pages: 113

Brand: IBM Pages: 16

Brand: IBM Pages: 214

Brand: Ultimaker Pages: 30

imageRUNNER ADVANCE C350iF

Brand: Canon Pages: 102

imageRUNNER ADVANCE C2230

Brand: Canon Pages: 12

Brand: Canon Pages: 598

Brand: Geeetech Pages: 52

Brand: Tally Pages: 106

Brand: Velleman Pages: 44

Magicolor 2530 DL

Brand: Konica Minolta Pages: 10

Brand: imagistics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands