Epson Stylus 1500 Service Manual Download Page 23

Page: 23 / 185

Font

This button selects the desired font.

Load/Eject

This button loads and ejects the paper.

❏

Pressing

Load/Eject

while holding down

Alt

starts the color printhead cleaning cycle.

Indicators

Operate (green)

Lights when printer power is on.

Data (orange)

❏

Lights when there is data in the print buffer.

❏

Blinks along with the

Pause

LED when an error occurs.

Black Ink Out (red)

Lights when there is no ink in the black ink cartridge, and blinks when the cartridge is low.

Color Ink Out (red)

Lights when there is no ink in the color ink cartridge, and blinks when the cartridge is low.

Paper Out (red)

Lights when the printer is out of paper, and blinks when a paper jam occurs.

Pause (orange)

Lights when printing is paused.

Economy (green)

Lights when economy printing mode is selected.

Condensed (green)

Lights when condensed printing mode is selected.

Font (green)

Shows the selected font.

Printer Features

1-16

EPSON Stylus 1500 Service Manual

Summary of Contents for Stylus 1500


























































































































































































Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands

Epson Stylus 1500, Service Manual

Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands