Epson Stylus 1500 Service Manual Download Page 56 | Manualshive

Page: 56 / 185

background image

Cap Mechanism

The cap mechanism prevents printhead nozzles from drying and keeps bubbles from forming
inside the nozzles while the printer is not in use.  The printer performs the capping operation
automatically when it is not printing.  If printer power is turned off during printing or ink system
operations, capping is performed and then turn off.  (The power switch is located in the secondary
circuit, which allows this operation to be performed.)  This printer has two caps: one for the black
printhead and one for the color printhead.

Wiping Mechanism

The wiping mechanism cleans the surface of the printhead when the printer is in the ink system
sequence.  When the paper feed drive motor rotates backward (CCW), power from the motor (via
the clutch unit and gears) is transmitted to the head cleaner (wiper) drive gear.  The head cleaner
moves across the carriage unit’s path.  When the motor rotates forward (CW), the head cleaner
moves toward the front to remove itself from the carriage unit’s path.  Both the black and color
printheads are cleaned by this wiper.

Color Cartridge (Option)

Carriage

Air Tube

C a p H ol d e r

C a p 1

C a p 2

A ir V a lv e

V a lv e S pr i n g

Black Printhead

Right Side Frame

1

1 '

Hinge

To Waste Ink Pad

To Waste Ink Pad

Figure 2-16. Cap Mechanism

Carriage Unit

Printhead

Head Cleaner

Head Cleaner Lever

PF Motor

Gear Train

Pump Gear / Clutch

Wiping Mechanism

Carriage Unit

Head Cleaner
Lever

Carriage Switch Lever

Disengage
Mechanism

Figure 2-17. Wiping Mechanism

Operating Principles

EPSON Stylus 1500 Service Manual

2-15

«
...
54
55
56
57
58
...
»

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Related manuals for Stylus 1500

Brand: 3D Systems Pages: 16

Brand: 3D Systems Pages: 28

Brand: 3D Systems Pages: 21

Brand: 3D Systems Pages: 25

Brand: 3D Systems Pages: 23

Brand: 3D Systems Pages: 35

Brand: 3D Systems Pages: 7

Brand: 3D Systems Pages: 13

Brand: 3D Systems Pages: 19

Brand: 3D Systems Pages: 13

Brand: 3D Systems Pages: 2

Brand: 3D Systems Pages: 2

Cubify CUBEX Duo

Brand: 3D Systems Pages: 10

Brand: 3D Systems Pages: 7

Brand: 3DGence Pages: 24

Brand: 3DGence Pages: 62

Brand: 3D Systems Pages: 5

Brand: Acadian Robotics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands