manualshive.com logo in svg

Epson Fast T-Jet 3 PLUS, User Manual, Page: 104 / 135

Share
Download
Epson Fast T-Jet 3 PLUS User Manual Download Page 104

T-Jet3 PLUS User’s Manual

Version 1.1  Revised July, 2008

94

Fill two 500 ml bottles (supplied) with HD cleaning solution.

11. 

12. 

Loosen one of the ink lines attached to the bulk ink

system bottles and connect it to one of the 

fi

 ttings on the 

cleaning solution bottle.

HINT: Completing this one ink line at a time will reduce 

spillage from any left over ink still in the ink lines.

13. 

Repeat step 12 for all of the ink lines so that

each line is connected to one of the 

cleaning solution bottles (CMYK for one and 

white for the other).

NOTE: Take care not to let  the lines tangle 

up. It’s important to make sure there are no 

kinks or creases in the ink lines.  

 

14. 

Remove one of the waste ink lines from the 

waste ink bottle.

Insert the tip of a plastic syringe (included) into the 

waste ink line and pull back on the plunger until 

the syringe is full of liquid. 

Dump the excess ink from the syringe into the 

waste ink bottle or other container.

Repeat step 14 for the remaining waste ink line.

15. 

Go back to the adjustment program on your computer.

16. 

Run multiple power cleanings until the solution that comes from the waste ink 

bottle is clear.

Summary of Contents for Fast T-Jet 3 PLUS








































































































































Reviews:

No comments