Epson AcuLaser C3900N User Manual Download

Page: 141 / 158

Error Messages (Warning)

This message...

means...

do this...

AUTH TIMEOUT

The user is automatically logged
off due to IEEE802.1X port
authentication.

Reauthorize the IEEE802.1X port, and
then log on.

DEVICE

NOT SUPPORTED

An incompatible device is
connected.

Do not connect an incompatible
device.

FUSER UNIT

END OF LIFE

The fuser unit has reached the
end of its life.

Replace the fuser unit and reset the
counter in the

MAINTENANCE MENU

SUPPLIES

REPLACE

FUSER UNIT

menu.

Note:

Printing can continue, however, the
printing result are not guaranteed.

HDD

NEAR FULL

The hard disk is full.

Delete print jobs saved on the hard
disk.

HUBS

NOT SUPPORTED

A USB hub is connected.

Do not connect a USB hub.

INCORRECT

HDD

Since the hard disk drive was
formatted with a different
machine, the hard disk drive
could not be used.

Replace the hard disk drive with one
compatible with this machine, or
select

HDD FORMAT

from

SYS

DEFAULT MENU

and format the hard

disk.

INCORRECT

P/U X

The

photoconductor unit is an

unapproved type.

Install a Epson photoconductor unit
of the appropriate type. See
“Replacing a Photoconductor Unit”
on page 87.

NONGENUINE

TONER X

The installed toner cartridge is
not a genuine Epson product.

Installing a genuine toner cartridge is
recommended.

P/U END

The

photoconductor unit has

reached the end of its life.

Replace the photoconductor unit.

P/U LIFE

The

photoconductor unit has

reached the end of its life.

Replace the photoconductor unit.
Printing continues until the message
“

P/U END

” appears.

P/U LOW

The

photoconductor unit is

nearly empty.
(Appears when

SYS DEFAULT

ENABLE WARNING

P/U

LOW

is set to

Prepare the specified color
photoconductor unit.

AcuLaser C3900 Series User’s Guide

Troubleshooting

141

Summary of Contents for AcuLaser C3900N































































































































































Search results

Summary of Contents for AcuLaser C3900N

Reviews:

Related manuals for AcuLaser C3900N

Brands by name

Popular brands

Epson AcuLaser C3900N, User Manual

Search results

Summary of Contents for AcuLaser C3900N

Reviews:

Related manuals for AcuLaser C3900N

Brands by name

Popular brands