Environnement AF22e Technical Manual Download Page 112

Page: 112 / 118

Environnement

S.A

AF22e

Duplication prohibited

JUNE 2016

5–14

Table 5–5 – Measurement board test points, LEDs description and connections

Jumpers Connections

Ribbon cable towards Interconnection board

Gas pressure sensor

Measurement chamber temperature sensor

Measurement chamber heating

J41

PM preamplifier board connector

J42 Photodiode

board

connector

Test points

Signal

PT1 GND

PT2 Analog

GND

PT41

PM signal (high gain amplification)

PT42

UV photodiode signal

PT43

PM HV setting

PT114

PM signal (low gain amplification)

LED N°

Identification

Color

Turned on

Turned off

Blinking

LED1

USB indicator

Green

Detected

Not detected

N.A.

LED2

Board activity indicator

Orange

Active

No activity

Fast, loading mode

Slow (1 Hz), normal
mode

LED3

Chamber heating supply

Red

Heater ON

Heater OFF

Regulation mode ON

LED4

5 V supply

Red

Active

N.A.

Summary of Contents for AF22e























































































































Search results

Summary of Contents for AF22e

Reviews:

Environnement AF22e, Technical Manual, Page: 112 / 118

Search results

Summary of Contents for AF22e

Reviews: