Emerson Smart Wireless Gateway 1420 Reference Manual Download Page 73

Page: 73 / 96

Table A-1: Emerson Wireless 1420 Gateway Ordering Information

(continued)

(7)

IECEx Type n

★

(7)

IECEx Dust

★

(7)

FM & CSA Division 2, Non-incendive and ATEX Type n

★

(7)

China Type n

★

(7)

TIIS Type n

★

Technical Regulation Customs Union (EAC) Type N

★

Redundancy Options

(8)

(9)

(10)

Gateway redundancy

★

Adapters

CM 20 conduit adapters

★

PG 13.5 conduit adapters

★

NPT conduit adapters

★

Antenna Options

(11)

WL2

Remote antenna kit, 50 ft. (15,2 m) cable, lightning arrestor

★

WL3

Remote antenna kit, 20 ft. (6,1 m) and 30 ft. (9,1 m) cables,
lightning arrestor

★

WL4

Remote antenna kit, 10 ft. (3,0 m) and 40 ft. (12,2 m) cables,
lightning arrestor

★

WN2

(12)

High-gain, remote antenna kit, 25 ft. (7,6 m) cable, lightning
arrestor

Typical Model Number: 1420 A 2 A3 A 2 N5

(1)

Single active 10/100 baseT Ethernet port with RJ45 connector.

(2)

Additional ports disabled.

(3)

Dual active 10/100 baseT Ethernet ports with RJ45 connectors.

(4)

Multiple active ports have separate IP addresses, firewall isolation, and no packet forwarding.

(5)

Convertible to RS232 via adaptor, not included with Gateway.

(6)

Includes Webserver, Modbus TCP, AMS Ready, HART-IP, and OPC.

(7)

Options may or may not come with POE. See terminal block configuration for determination if
the device is compatible with POE.

(8)

Requires the selection of Dual Ethernet option code 2.

(9)

Not available with DeltaV Ready option code 5.

(10)

Not available with EtherNet/IP option codes 8 and 9.

(11)

The WL2, WL3, WL4, and WN2 options require minor assembly.

(12)

Not available in all countries.

A.8

Accessories and spare parts

Table A-2: Accessories

Item description

Part number

AMS Wireless SNAP-ON

™

, 1 Gateway license

01420-1644-000
1

Reference Manual

Specifications and Reference Data

00809-0200-4420

September 2020

Emerson.com/Rosemount

Summary of Contents for Smart Wireless Gateway 1420

































































































Search results

Summary of Contents for Smart Wireless Gateway 1420

Reviews:

Related manuals for Smart Wireless Gateway 1420

Brands by name

Popular brands

Emerson Smart Wireless Gateway 1420, Reference Manual

Search results

Summary of Contents for Smart Wireless Gateway 1420

Reviews:

Related manuals for Smart Wireless Gateway 1420

Brands by name

Popular brands