manualshive.com logo in svg

Emerson Smart Wireless Gateway 1420, Reference Manual

Share
Download
Emerson Smart Wireless Gateway 1420 Reference Manual Download Page 53

Table 5-2: Predefined Modbus Registers

 (continued)

Description

Register

Data type

SYSTEM_DIAG.TEST_UNSIGNED_BYTE

49033

8-bit unsigned int

SYSTEM_DIAG.TEST_SHORT

49034

16-bit int

SYSTEM_DIAG.TEST_UNSIGNED_SHORT

49035

16-bit unsigned int

SYSTEM_DIAG.TEST_INT

49036

32-bit int

SYSTEM_DIAG.TEST_UNSIGNED_INT

49038

32-bit unsigned int

SYSTEM_DIAG.TEST_FLOAT

49040

32-bit float

5.5

EtherNet/IP

5.5.1

EtherNet/IP Communication settings

It is important that the Ethernet/IP communication settings in the Gateway match the
setting in the Ethernet/IP master or client. Refer to host system documentation for more
information on how to configure these settings or to the Emerson Wireless Gateway
Integration 

Reference Manual

 for Ethernet/IP. The Ethernet/IP communication settings

can be found by navigating to 

System Settings

 

→

 

Protocols

 

→

 

EtherNet/IP

. Network

architectures should reflect that of a DeltaV

™

system see 

#unique_72/

unique_72_Connect_42_Ram24704

.

Note

Ethernet/IP can be integrated with any approved Ethernet/IP ODVA member. Other
protocols such as HARTIP are still functional within the Gateway. See the Emerson Wireless
Gateway 

Product Data Sheet

 for ordering options.

Reference Manual

Operation and Maintenance

00809-0200-4420

September 2020

Emerson.com/Rosemount

53

Summary of Contents for Smart Wireless Gateway 1420

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands