manualshive.com logo in svg

Emerson Smart Wireless Gateway 1420, Reference Manual

Share
Download
Emerson Smart Wireless Gateway 1420 Reference Manual Download Page 2

Safety Messages

NOTICE

Read this manual before working with the product. For personal and system safety, and for optimum product performance, make
sure you thoroughly understand the Contents before installing, using, or maintaining this product.

 WARNING

Failure to follow these installation guidelines could result in death or serious injury.

Ensure only qualified personnel perform the installation.

Explosions could result in death or serious injury.

Verify that the operating atmosphere of the transmitter is consistent with the appropriate hazardous locations certifications.

Electrical shock could cause death or serious injury.

If the device is installed in a high-voltage environment and a fault condition or installation error occurs, high voltage may be
present on transmitter leads and terminals.
Use extreme caution when making contact with the leads and terminals.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
This device must be installed to ensure a minimum antenna separation distance of 20 cm from all persons.

The products described in this document are NOT designed for nuclear-qualified applications. Using non-nuclear qualified
products in applications that require nuclear-qualified hardware or products may cause inaccurate readings.For information on
Rosemount

™

 nuclear-qualified products, contact your local Emerson Sales Representative.

2

Summary of Contents for Smart Wireless Gateway 1420

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands