Emerson Smart Wireless Gateway 1420 Reference Manual Download Page 60

Page: 60 / 96

Table 6-4: Troubleshooting Modbus Communications

(continued)

Issue

Troubleshooting steps

Can not communicate
using secure Modbus
TCP

1. Verify the Security Setup Utility has been installed.

2. Configure a Secure Modbus Proxy for the Gateway. See

Section 4:

Commissioning

3. Verify secure/unsecure Modbus protocol settings in the Gateway.

Log on to the Gateway and navigate to

SETUP

→

SECURITY

→

PROTOCOLS

4. Verify the Modbus TCP communications settings in the Gateway.

Log on to the Gateway and navigate to

SETUP

→

MODBUS

→

COMMUNICATIONS

5. Verify Modbus register mapping in the Gateway. Log on to the

Gateway and navigate to

SETUP

→

MODBUS

→

MAPPING

Table 6-5: Troubleshooting OPC Communications

Issue

Troubleshooting steps

OPC application can not find a
Gateway OPC server

1. Verify the Security Setup Utility has been installed on the

same PC as the OPC application.

2. Configure an OPC proxy for the Gateway. See

Section 4:

Commissioning

Gateway OPC server does not
show any Gateways

1. Configure an OPC proxy for the Gateway. See

Section 4:

Commissioning

Gateway OPC server does not
show any data tags

1. Configure the Gateway OPC Browse Tree. Log on to the

Gateway and navigate to

SETUP

→

OPC

→

OPC BROWSE

TREE

2. Verify the connection status for the OPC proxy in the

Security Setup Utility.

3. Verify if the OPC proxy is configured for secure or unsecure

communications.

4. Verify secure/unsecure OPC protocol settings in the

Gateway. Log on to the Gateway and navigate to

SETUP

→

SECURITY

→

PROTOCOLS

5. Verify network firewall and port settings.

Table 6-6: Troubleshooting EtherNet/IP

Issue

Troubleshooting steps

The Gateway is not publishing
the parameters

1. Verify connection is established with Ethernet/IP. Navigate

SETUP

→

SECURITY

→

PROTOCOLS

2. Reference

Emerson Wireless Gateway to Allen-Bradley

Integration Manual

Troubleshooting

Reference Manual

September 2020

00809-0200-4420

Emerson.com/Rosemount

Summary of Contents for Smart Wireless Gateway 1420

































































































Search results

Summary of Contents for Smart Wireless Gateway 1420

Reviews:

Brands by name

Popular brands

Emerson Smart Wireless Gateway 1420, Reference Manual

Search results

Summary of Contents for Smart Wireless Gateway 1420

Reviews:

Brands by name

Popular brands