manualshive.com logo in svg

Emerson Smart Wireless Gateway 1420, Reference Manual

Share
Download
Emerson Smart Wireless Gateway 1420 Reference Manual Download Page 43

5

Operation and Maintenance

5.1

Overview

This section describes how to connect the Emerson

™

 Wireless 1420 Gateway (Gateway) to

a host system and integrate data gathered from the field device network. It covers
network architectures, security, and data mapping.

In accordance with WirelessHART

®

 security guidelines, the Gateway should be connected

to the host system via a LAN (Local Area Network) and not a WAN (Wide Area Network).

5.2

Network architecture

Physical connection types are important when determining the network architecture and
what protocols can be used for integration. Ethernet is the primary physical connection
type and RS-485 is available as an optional connection type. The following network
architecture diagrams will help when integrating data from the Gateway into the host
system.

5.2.1

Ethernet

An Ethernet connection supports Modbus

®

 TCP, OPC, AMS Wireless Configurator,

Ethernet/IP

™

, and HART

®

 TCP protocols. Using this connection type, the Gateway is wired

directly to a control network (see 

Figure 5-1

) using a network switch, router, or hub. There

are often two networks for redundancy purposes.

Reference Manual

Operation and Maintenance

00809-0200-4420

September 2020

Emerson.com/Rosemount

43

Summary of Contents for Smart Wireless Gateway 1420

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands