manualshive.com logo in svg

Emerson Smart Wireless Gateway 1420, Reference Manual, Page: 71 / 96

Share
Download
Emerson Smart Wireless Gateway 1420 Reference Manual Download Page 71

Figure A-2: Remote Omni-Antenna Kit

WL2

WL4

WL3

WN2

A

A

A

A

B

C

D

D

D

D

E

E

F

G

H

I

A. Antenna

B. 2 ft. (6,1 m) cable

C. 10 ft. (3,0 m) cable

D. Lightning arrestor

E. Interchangeable cables
F. 50 ft. (15,2 m) cable

G. 30 ft. (9,1 m) cable
H. 40 ft. (12,2 m) cable

I. 25 ft. (7,6 m) cable

A.6.1

Remote omni-antenna kit

The remote omni-antenna kit includes sealant tape for remote antenna connection, as
well as mounting brackets for the antenna, lightning arrestor, and the Smart Wireless
Gateway.

Lightning protection is included on all the options. WL3 and WL4 provide lightning
protection along with the ability to have the Gateway mounted indoors, the antenna
mounted outdoors, and the lightning arrestor mounted at the building egress.

Reference Manual

Specifications and Reference Data

00809-0200-4420

September 2020

Emerson.com/Rosemount

71

Summary of Contents for Smart Wireless Gateway 1420

































































































Reviews:

No comments