Emerson Control Techniques Epsilon Eb-202 Installation Manual Download

Page: 34 / 134

Installation

• All inductive coils must be suppressed with appropriate devices, such

as diodes or resistor/capacitor (RC) networks.

Mechanical Installation

Drive Mounting

Drives must be back mounted vertically on a metal surface

such as a NEMA enclosure. A minimum spacing of two inches

must be maintained above and below the drive for ventilation.

Side by side drive spacing requirements vary by drive size and

RMS loading. Additional space may be necessary for wiring

and cable connections.
For drive dimensions, weights and mounting specifications, see

the "Specifications" section.

Motor Mounting

Motors should be mounted firmly to a metal mounting surface

to ensure maximum heat transfer for maximum power output

and to provide a good ground.
For motor dimensions, weights and mounting specifications,

see the "Specifications" section.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews:

Related manuals for Control Techniques Epsilon Eb-202

Brands by name

Popular brands

Emerson Control Techniques Epsilon Eb-202, Installation Manual

Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews:

Related manuals for Control Techniques Epsilon Eb-202

Brands by name

Popular brands