Emerson Control Techniques Epsilon Eb-202 Installation Manual Download Page 61

Page: 61 / 134

Epsilon Eb Digital Servo Drive Installation Manual

Figure 29:

Master/Slave Encoder Connections

Note

Epsilon encoder outputs meet RS-422 driver specifications

and can drive up to 10 RS-422 signal recievers. Each

Epsilon differential pulse input is an RS-422 line recievers.

The default encoder output resolution is 2048 lines per

motor revolution. This resolution is adjustable in one line

per revolution increments with PowerTools software. The

range is between 200 and the actual motor encoder density.

Serial Communications

Serial communications with the drive is provided through the

female DB-9 connector located on the front of the drive. The

serial interface is either three wire non-isolated RS-232C or

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews:

Emerson Control Techniques Epsilon Eb-202, Installation Manual, Page: 61 / 134

Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews: