manualshive.com logo in svg

Emerson Control Techniques Epsilon Eb-202, Installation Manual, Page: 43 / 134

Share
Download
Emerson Control Techniques Epsilon Eb-202 Installation Manual Download Page 43

28

Epsilon Eb Digital Servo Drive Installation Manual

 Figure 12:

Epsilon Auxiliary Power Supply Wiring Diagram

Alternate Power Supply Wiring

An Alternate Power Supply (APS) allows the drive to retain 

motor position information and serial communications when 

the main AC power supply is disconnected. You must reset the 

drive, either using the reset button or a reset input, after AC 

power is re-applied if the backup supplies have been active.
Enabling APS power is done by sliding open the access panel on 

the side of the drive. Then move the jumper into the APS 

position using needle nose pliers.

Side View

Front View

24 VDC

Important:

 Slide the side access panel

up into the open position. Remove the
jumper from the AC position (Default)
and reinstall it into the 24 V position
(A.P.S.). The instruction on the side of
the drive will show which position to put
the jumper.

J1

+

-

2 A

Fuse

Single point PE

ground

(recommended)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Reviews:

No comments