Emerson Control Techniques Epsilon Eb-202 Installation Manual Download Page 29

Page: 29 / 134

Epsilon Eb Digital Servo Drive Installation Manual

• Encoder chassis and electrical connector
A good rule to follow when specifying conductors for high

frequency applications is to use a metal strap with a length to

width ratio that is less than 3:1.

AC Line Filters

The AC line filters used during EMERSON Motion Control’s

compliance testing are listed below. These filters are capable of

supplying the drive input power to the specified drive under

maximum output power conditions.

Alternately, EMERSON Motion Control has also seen good

results with the following line filters:

AC Line Filter Installation Notes

• EMC criteria can be met in installations where multiple

drives are supplied through a single filter, however, it is the

installers responsibility to verify EMC compliance.

Questions on this subject should be directed to the filter

manufacturer.

Epsilon

E Series

Schaffner Part #

EMERSON Part #

Rating

Eb-202, Eb-203*

FN2070-10/08

960307-01

10A, 240V, 1 Ø

EN-204

FS5278-16/08

960305-01

16A, 240V, 1 Ø

Eb-205

EN-208

FS5278-16/08

960305-01

EN-214

FN-258/16

960304-01

16A, 480V, 3 Ø

Drive

Part #

Rating

EN-204

Corcom

20EQ1

20A, 240V, 1 Ø

EN-208

Eb-202, Eb-203, Eb-205

Eb-202

Schaffner FN 2070-6-06

6A, 240V, 1 Ø

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews:

Emerson Control Techniques Epsilon Eb-202, Installation Manual, Page: 29 / 134

Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews: