Emerson Control Techniques Epsilon Eb-202 Installation Manual Download Page 9

Page: 9 / 134

Underwriters Laboratories Listed

The Epsilon Digital Servo Drives are marked with the “UL

Listed” label after passing a rigorous set of design and testing

criteria developed by UL (UL508C). This label indicates that

UL certifies this product to be safe when installed according to

the installation guidelines and used within the product

specifications.

The “conditions of acceptability” required by UL are:

• The Epsilon drive surrounding air ambient temperature

must be 40° C (104° F) or less.

• Epsilon drive surrounding air ambient temperature can be

up to 50°C (122° F) with 3% linear derating for every degree

above 40° C (104° F)

• This product is suitable for use on a circuit of delivering not

more than 5000 RMS symmetrical amperes, 240 volts

maximum.

• Motors must incorporate an overload protection device such

as an overtemperature switch.

Drive Overload Protection

The drive output current overload protection is provided by the

drive and is not adjustable. This overload protection is based on

maximum continuous output current capacity. It will allow up

to 200 percent of the drive rated current to be delivered for the

amount of time determined by the following chart.

LISTED 51Y8

IND. CONT. EQ.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews:

Emerson Control Techniques Epsilon Eb-202, Installation Manual, Page: 9 / 134

Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews: