manualshive.com logo in svg

Emerson Control Techniques Epsilon Eb-202, Installation Manual, Page: 36 / 134

Share
Download
Emerson Control Techniques Epsilon Eb-202 Installation Manual Download Page 36

21

Installation

Power Supply Requirements

The examples below show AC power connections for single 

phase and three phase drives. These examples are shown for 

reference only. Local electrical codes should be consulted before 

installation.

Warning

The Protective Earth (PE) wire connection is mandatory for 

human safety and proper operation. This connection must 

not be fused or interrupted by any means. Failure to follow 

proper PE wiring can cause death or serious injury.

The Eb-202, Eb-203 and Eb-205 drives require 42 to 264 VAC 

single-phase power. An Epsilon drive can be connected to any 

pair of power phases on a 1 Ø or 3 Ø power source that is 

grounded as shown in the following diagrams.
If using an APS Logic Power input and the Low DC Bus fault 

is disabled, minimum supply voltage to an Epsilon can be 

reduced to 15 VAC on the AC inputs or 24 VDC on the Bus +/- 

connections.

Note

The maximum voltage applied to the drive terminals must 

not exceed 264 VAC phase to phase and phase to PE ground. 

This can be accomplished by referencing the AC supply to 

earth ground.

Caution

Do not connect or disconnect the AC power by inserting or 

removing the AC power connector. Using the connector in 

this manner, even once, will damage the connector, making 

it unusable.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Reviews:

No comments