Emerson Control Techniques Epsilon Eb-202 Installation Manual Download Page 84

Page: 84 / 134

Options and Accessories

Use tie wraps to provide a strain relief and a ground connection

at the shield connection points.
If you do not wish to use the DIN rail mounting hardware, the

ECI-44 can be disassembled and the mounting clips removed.
The ECI-44 wire range is #18 to 24 AWG stranded insulated

wire.

Note

Wiring should be done with consideration for future

troubleshooting and repair. All wiring should be either color

coded and/or tagged with industrial wire tabs. Low voltage

wiring should be routed away from high voltage wiring.

STI-EIO Interface

The STI-EIO interface allows access to all digital input and

output signals. The STI-EIO mounts directly to the J3

connector on the drive. See Figure 40 on page 70.

Note

Shield connection points are connected to the shell of the 44-

pin “D” connector on the STI EIO.

The STI-EIO wire range is #18 to 24 AWG stranded insulated

wire.

Note

Wiring should be done with consideration for future

troubleshooting and repair. All wiring should be either color

coded and/or tagged with industrial wire tabs. Low voltage

wiring should be routed away from high voltage wiring.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews:

Emerson Control Techniques Epsilon Eb-202, Installation Manual, Page: 84 / 134

Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews: