Emerson Control Techniques Epsilon Eb-202 Installation Manual Download Page 17

Page: 17 / 134

Epsilon Eb Digital Servo Drive Installation Manual

The MG and NT motors that are matched to the Epsilon drives

provide low inertia, high power to size ratios, and encoder

feedback for accurate positioning.

Features

• Digital drive design using DSP, ASIC and surface mount

technologies.

• Epsilon input power is rated at 42 to 264 VAC (12 to 264

VAC or 12 to 375 VDC when using an A.P.S.).

• Small mounting footprint.
• Auxiliary logic power supply capability.
• Five optically isolated inputs and three optically isolated

outputs.

• Built-in RS-232C to RS-485 converter for multi-drop

applications.

• RS-232C/485 serial communications interface using

industry standard Modbus® protocol up to 19.2 kbaud.

• Diagnostic and operating mode status display.
• Extensive fault sensing and diagnostics, including storage

and time stamping of the last ten faults.

• Maximum input response time is 500 µs for command and

input functions.

• Peak torque up to three times continuous motor torque

rating 200% for 5 seconds.

• Sinusoidal commutation for efficiency and motor smooth

motion.

• No potentiometers or selector switches.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Control Techniques Epsilon Eb-202







































































































































Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews:

Emerson Control Techniques Epsilon Eb-202, Installation Manual, Page: 17 / 134

Search results

Summary of Contents for Control Techniques Epsilon Eb-202

Reviews: