53
z
Cleaning the Looper Threader Pipe
CAUTION
Make sure to turn the power switch off before cleaning
the machine.
q
q
w
q
e
r
t
y
x
c v b n
m
,
NOTE:
• Clean the looper threader pipe once every 10
hours of use or when the looper threader does not
work well.
• You can also use an compressed air duster or
camera dust blower to clean the looper threader
pipe.
Use the looper threading wire to clean the pipe of the
looper threader device.
z
Open the looper cover and set the looper threader
switch lever to the “THREADING” position.
q
Looper threader switch lever
urn the handwheel toward you slowly until it clicks.
w
Handwheel
c
Insert the straight end (not the looped end) of the
looper threading wire into the hole of the looper
threader until it comes out from the looper tip hole.
e
Straight end of the looper threading wire
r
Looper threader hole
v
Prepare a 60 cm length of size 60 thread and pass
it halfway (30 cm) through the loop of the looper
threading wire so that the both ends meet as
illustrated.
t
30 cm
b
Pull the looper threading wire out together with the
thread.
n
Repeat steps
c
–
b
two or three times.
m
With the machine unthreaded, raise and lower the
looper threader lever four or five times to clean out the
remaining lint.
y
Looper threader lever
,
Return the looper threader switch lever to the
“SEWING” position and close the looper cover.
x
Čišćenje cevi uvlakača donjeg petljača
PAŽNJA
Obavezno isključite glavni prekidač pre čišćenja
mašine.
Koristite šicu za uvlačenje konca za čišćenje cevi
donjeg uvlakača.
Otvorite poklopac petljača i postavite ručicu
prekidača uvlakača donjeg konca na "THREADING"
Ručica prekidača uvlakača donjeg konca
Okrenite polako zamajac ka sebi dok ne klikne.
Zamajac
Ubacite ravan kraj (ne kraj sa petljom) žice za
uvlačenje konca u otvor uvlakača konca petljača
da izađe iz otvora na vrhu petljača.
Ravan kraj žice za uvlačenje konca
Otvor na vrhu petljača
Pripremite 60 cm dugačak konac debljine 60 i
provucite ga do polovine (30 cm) kroz petlju na
žici za uvlačenje konca tako da oba kraja budu
kao što je prikazano na slici levo.
Izvucite žicu za uvlačenje konca zajedno sa koncem.
Ponovite korak
dva ili tri puta.
Dok je mašina bez konaca, podignite i spustite
polugu uvlakača konca petljača četiri ili pet puta
da očistite preostale ostatke tkanine i konca.
Poluga uvlakača petljača
Vratite ručicu prekidača uvlakača donjeg konca
na položaj "SEWING" i zatvorite poklopac petljača.
NAPOMENA:
Očistite cev uvlakača petljača na svakih 10 sati
upotrebe ili kada ne radi kako treba.
Možete koristiti kompresor za prašinu ili duvač
prašine za kamere da očistite cev uvlakača konca
petljača.
Summary of Contents for eXtend 864air
