36
Securing Ends
To avoid raveling, you need to leave a thread chain
approximately 2˝ (5 cm) long at the beginning and at the
end of a seam. To secure the beginning and end of a
seam, choose one of the following methods.
At the beginning of the seam
A. Separate and tie the thread ends together.
B. Thread the chain through a large eyed needle, and
weave that chain through the overlock stitches on the
fabric.
C. Cut the chain at the edge of the fabric, and apply a
small amount of seam sealant (Fray Check™ or Fray-
No-More™) to the thread ends.
D. Securing the beginning with the machine
z
Before putting your fabric in the machine, sew a
thread chain approximately 2˝ (5 cm) long behind
the needle.
x
Put your fabric on the machine. Serge a few
stitches and stop.
c
Raise the presser foot and bring the thread chain
to the left around and under the presser foot.
v
Place the thread chain between the presser foot
and upper knife, holding it in position as you lower
the presser foot to sew.
b
After sewing approximately 1˝ (2.5 cm), move the
chain to the right and under the upper knife, cutting
the chain as you sew.
D
A
B
C
At the end of the seam
Securing the seam end with the machine
z
Serge one stitch off the end of the seam.
x
Raise the needle and presser foot, and gently pull the
threads off the chaining finger.
c
Turn the fabric over so that the under side is up.
v
Serge approximately 1˝ (2.5 cm) over the stitching and
angle off the fabric.
E
Cutting the Seams
Cut the upper looper thread with a seam ripper (not
included with the machine) to cut the seams.
q
Upper looper thread
w
Seam ripper
q
w
z
z
x c v b
x c
v
Učvršćivanje konaca šava
Da sprečite paranje šava, na početku i na kraju šava
ostavite najmanje 5 cm dugačak lanac konca.
Da učvrstite šav, pratite jedan od sledećih postupaka.
Raspletite niti lančića i vežite ih čvorom.
Uvucite kraj lančića u iglu za šivenje sa velikim ušicama
i provucite ga kroz overlok šav na tkanini.
Odsecite lančić tik uz ivicu tkanine, a zatim na kraj šava
nanesite malo lepka za tkaninu
ili
Učvršćivanje početka šava mašinom
Pre nego što tkaninu postavite u mašinu, prošijte
lanac dužine 5 cm.
Postavite tkaninu u mašinu i prošijte nekoliko
bodova, a zatim se zaustavite.
Podignite stopicu i povucite lanac ulevo, oko i
ispod stopice.
Stavite lančić između stopice i gornjeg noža,
držeći ga tako da možete spustiti stopicu i
početi da šijete.
Prošijte približno 2.5 cm dugačak šav.
Zatim povucite lančić udesno i pod gornji nož
za odsecanje tkanine i odsecite ga tokom šivenja.
Na kraju šava
Učvršćivanje kraja šava mašinom
Prošijte tkaninu za jedan bod više nego što je potrebno.
Podignite iglu i stopicu i pažljivo izvucite lančić sa
prsta ubodne ploče.
Okrenite tkaninu tako da donja strana bude okrenuta gore.
Prošijte približno 2.5 cm preko bodova koje ste već uradili,
tako da novi šav bude pod blagim uglom i da ne presečete
postojeći šav.
Paranje šava
Presecite paralicom konac gornjeg petljača (nije uključena
u standardni pribor mašine).
Konac gornjeg petljača
Paralica
Summary of Contents for eXtend 864air
