Looper selection lever
Turn the looper selection lever to the right to
thread the lower looper.
Turn the looper selection lever to the left to
thread the upper looper.
.
Using the tweezers, insert the end of the thread 1˝
(2 cm) or more into the threading hole on the right.
!1
Tweezers
!2
Threading hole on the right
!3
Thread (12˝ (30 cm) or longer)
!4
Thread end (1˝ (2 cm) or longer)
b
Pull out approximately 12˝ (30 cm) of thread. Make
sure that the thread does not get tangled around the
lever or the cover.
u
Thread
n
Set the looper threader switch lever to the
“THREADING” position.
i
Looper threader switch lever
Adjusting the looper threader switch lever
Set the looper threader lever to the
“THREADING” position by turning it to the right.
Set the looper threader lever to the “SEWING”
position by turning it to the left.
m
Turn the handwheel toward you slowly until it clicks.
This locks the handwheel in place.
o
Handwheel
,
Turn the looper selection lever to the “UPPER LOOPER”
position.
!0
Looper selection lever
NOTE:
• Trim the thread end so that it can be inserted into
the threading hole smoothly.
• If threading special threads, such as wooly nylon,
etc., refer to pages 26 and 27.
23
!1
!2
!3
!4
u
i
o
!0
b n
m
,
.
b n
m
.
,
Izvucite približno 30cm konca. Uverite se da se konac
nije zapetljao oko poluge ili poklopca.
Konac
Postavite ru
č
icu prekida
č
a uvlaka
č
a donjeg konca
na poziciju "PROVLA
Č
ENJE KONCA".
Ru
č
ica prekida
č
a uvlaka
č
a donjeg konca
Podešavanje ru
č
ice prekida
č
a uvkala
č
a donjeg konca
Postavite ru
č
icu prekida
č
a uvlaka
č
a donjeg
konca na poziciju "PROVLA
Č
ENJE KONCA"
tako što
ć
ete je pomeriti udesno.
Postavite ru
č
icu prekida
č
a uvlaka
č
a donjeg
konca na poziciju "ŠIVENjE" tako što
ć
ete
je pomeriti ulevo.
Polako okrenite zamajac ka sebi, dok ne klikne.
Tako
ć
ete ga zaklju
č
ati na mestu.
Zamajac
Postavite polugu za izbor petlja
č
a u poziciju "GORNjI
PETLJA
Č
".
Poluga za izbor petlja
č
a
Okrenite polugu za izbor petlja
č
a udesno
da provu
č
ete konac kroz donji petlja
č
.
Okrenite polugu za izbor petlja
č
a ulevo
da provu
č
ete konac kroz gornji petlja
č
.
Uz pomo
ć
pincete, ubacite kraj konca dužine 2cm ili
više u desni otvor za provla
č
enje konca.
Pinceta
Desni otvor za provla
č
enje konca
Konac (dužine 30cm ili više)
Konac (dužine 2cm ili više)
NAPOMENA:
Odsecite vrh konca, tako da možete lako da ga
ubacite u otvor.
Ako koristite specijalne vrste konca, pogledajte
uputstva na stranama 26 i 27.
Summary of Contents for eXtend 864air
