ELECTRO FREEZE 99T-RMT Operator'S Manual Download Page 52

Page: 52 / 98

184621

ELECTRO FREEZE Soft Serve Model 99T-RMT

12 Troubleshooting Tables

(continued)

PROBLEM

PROBABLE CAUSE

REMEDY

1. Pr

oduct too cold.

Check product temperature. Should be
18°F (-7.8°C). See Dispensed Product
Too Cold.

Low overrun.

Check air meter. If plugged, clean. See
MTS Troubleshooting-No Air (Overrun).

MTS problem.

See MTS Troubleshooting Charts

Product
dispenses
slowly out of
dispensing
head.

Dispensed speed set to slow.

Contact your Electro Freeze distributor
for service.

1. Low overrun.

1. Check overrun, if low see MTS

Troubleshooting Chart.

2. Cylinder thermostat erratic or set too

cold.

2. Contact your Electro Freeze Distributor

for service.

3. Plunger switch electrically or

mechanically stuck closed.
(Unit runs all the time.)

3. Contact your Electro Freeze Distributor

for service.

4. Component failure.

4. Contact your Electro Freeze Distributor

for service.

5. Low suction pressure, refrigeration

system.

5. Contact your Electro Freeze Distributor

for service.

Dispensed
product too
hard.

6. Dispensed speed set to slow.

6. Contact your Electro Freeze Distributor

for service.

Blades installed upside down.

1. Install properly – flat side to cylinder

wall.

Dirty or blocked condenser, restricted air
flow.

2. Unblock condenser or have cleaned by

your Electro Freeze Distributor.

Component failure.

3. Contact your Electro Freeze Distributor.

Dispensed
product too
soft. (Product
temperature
above 19°F
[-7.2°C] )

Leak in refrigeration system resulting in
little or no refrigeration.

4. Contact your Electro Freeze Distributor.

Summary of Contents for 99T-RMT



































































































Search results

Summary of Contents for 99T-RMT

Reviews:

Related manuals for 99T-RMT

Brands by name

Popular brands

ELECTRO FREEZE 99T-RMT, Operator'S Manual

Search results

Summary of Contents for 99T-RMT

Reviews:

Related manuals for 99T-RMT

Brands by name

Popular brands