ELECTRO FREEZE 99T-RMT Operator'S Manual Download

Page: 15 / 98

ELECTRO FREEZE Soft Serve Model 99T-RMT

184621

Part Names and Functions

(continued)

PLUNGER - CENTER

Seals the product opening in the
dispense head when closed.
Allows product to flow when
open.

PIN - HANDLE

Secures the handle to the dis-
pense head.

10 HANDLE - DISPENSE

(SIDE)

Opens and closes the plunger to
start and stop the flow of product
from the freezer.

11 KNOB - HAND

Secures the dispense head to the
freezing cylinder.

12 HANDLE - DISPENSE

(CENTER)

Opens and closes the plunger to
start and stop the flow of product
from the freezer.

13 NOZZLE - SERRATED

Forms the frozen product as it is
dispensed.

HEAD

Encloses the freezing cylinder and
provides an opening for product to
be dispensed.

O-RING - PLUNGER

Seals the plunger in the head. Must
be lubricated to seal and slide
properly.

O-RING - HEAD

Seals the head to the freezing
cylinder. Must be lubricated.

PLUNGER - SIDE

Seals the product opening in the
dispense head when closed. Allows
product to flow when open.

O-RING - PLUG

Seals the air bleed plug in the
dispense head.

PLUG - AIR BLEED

Seals the air bleed opening in the
dispense head when closed. Allows
excess air to be removed from the
cylinder in the filling process.

PUSH ROD - PLUNGER

Starts the freezer when dispensing.
Must be in place before freezer will
operate.

The following descriptions apply to figure 4-1. The number preceding the
part name corresponds to the number in the figure.

Summary of Contents for 99T-RMT



































































































Search results

Summary of Contents for 99T-RMT

Reviews:

Related manuals for 99T-RMT

Brands by name

Popular brands

ELECTRO FREEZE 99T-RMT, Operator'S Manual

Search results

Summary of Contents for 99T-RMT

Reviews:

Related manuals for 99T-RMT

Brands by name

Popular brands