background image

ELECTRO FREEZE Soft Serve Model 99T-RMT

184621

      

  31

9

   Closing Procedures

9.1    Night Switch Operation

1. In areas where health codes

will allow, the freezer may be switched
to night operation which will allow the
freezer to cycle all night and maintain
approximately 38°F (3°C) or lower
product in the cylinders and cabinet.

2. To switch the freezer to the

night mode, leave the SELECTOR
switches on “AUTO”  (1, Figure 9-1)
and the cabinet switch “ON” (4).

3. Turn the MTS switches to the

“OFF” (3) position.

4. Turn the DAY/NIGHT switches

to “NIGHT” (2) and let the machine
cycle.

5. Remove serrated nozzles and

clean the drip tray assembly and all soiled
surfaces with soap and water.  Use
sanitizing solution in spray bottle and
brush to clean the bottom of the plunger
openings.

6.

To start the machine after using

the NIGHT mode, turn the DAY/NIGHT
switches to “DAY” (2) and the MTS
switches to “ON” (3).  Before replacing
sanitized nozzles use a small brush and
sanitizer to clean the bottom of the
plunger openings.

Figure 9-1

Summary of Contents for 99T-RMT



































































































Reviews: