ELCOM Uniq 150, Service Manual

Page: 20 / 41

32
Elcom, spoločnosť s ručením obmedzeným, Prešov Elcom, spoločnosť s ručením obmedzeným, Prešov
33
Uniq 150 Service manual Service manual Uniq 150
2.13.3. WiFi installation into milled covers
Some of the Uniq 150 covers has already milled cavities for setting WiFi antennas. In this case is more suitable set
antennas in those cavities.
1. Screw adapter to WiFi module.
2. Connect WiFi module with adapter to miniPCI connector CN4 (N270) or CN1 (D525) of mainboard.
3. Antennas cables connect to MAIN and AUX connectors of WiFi module.
4. Stick doublesided tape on both antennas from the side of cable. Let one side of tape covered, because antennas will
be sticked already after closing front and rear cover. Stick antennas into cavities. Defat cavities before sticking.
Figure 2.13.3. – WiFi installation into milled covers
Rear cover
WiFi antenna
cable of WiFi antenna
rear cover cavity
side strip cutting
Side strip
top cover cavity
Front cover
Mini PCIe full size card (adapter)
WPER-101GN(BT) mini PCIe
WiFi module
Screw of MiniPCIe card adapter
Needed to order Quantity Ord. code
WiFi PCB antenna L = 400 mm
2,4G PCB antenna L=400mm
2
2
M310022
M310144
Doublesided sticker tape TESA 6 mm 2 × 50 mm M990098
WPER-101GN(BT) mini PCIe WiFi module
Wifi interny s BT mPCIe WPEA
1
M310023
M310122
Intel 6235 wifi s BT mPCIe 1 M310111
Mini PCIe full size card 1 M310024
Screw of MiniPCIe card adapter 2 M310025
2.14. Interconnection and installation of VGA port
VGA port is connected to mainboard to connector VGA1 (Uniq PC) or to connector CN1 (Uniq Display).
Owing to VGA connector installation for Nx execution is necessary to assembly extended connectors holder.
2.14.1. Interconnection of VGA port for Nx execution
1. Insulate end of cable and put tubing on individual wires.
2. Solder connectors on the cable.
3. Soldered places cover with tubing and shrink them with hot air.
Needed to order Quantity Ord. code
Tubing 1,6 × 10 mm 20 M010003
Flat cable RM1mm 40pin colored 0,3 m M200155
Connector VGA D-SUB 15M 3-row for cable 1 M190119
Connector VGA D-SUB 15F 3-row for cable 1 M190029
2.14.2. Interconnection of VGA port for Tx execution
1. Insulate end of cable and put tubing on individual wires.
2. Solder connectors on the cable.
3. Soldered places cover with tubing and shrink them with hot air.
4. Put covers on connectors.
Needed to order Quantity Ord. code
Tubing 1,6 × 10 mm 20 M010003
Cable CAB8 9 × 0,22 mm shielded 2 m/3 m * M200009
Connector VGA D-SUB 15M 3-row for cable 1 M190119
Connector VGA D-SUB 15F 3-row for cable 1 M190029
Covers for Canon 9 2 M190006
* Use 2 m of cable for 50 cm TH and 3 m of cable for 130 cm TH.
Figure 2.14. – Interconnction of VGA port
D-SUB HD 15M D-SUB HD 15F
1
2
3
5, 7, 8, 10
6
9
12
13
14
15
1
2
3
5, 7, 8, 10
6
9
12
13
14
15
—
—
—
—
—
—
—
—
—
—
Pin number 5, 7, 8 and 10 solder together on both
connectors and lead them through one wire.
Pin number 4 and 11 do not connect.
to conn. VGA1 on MB (15M)
external VGA conn. (15F)
Front view
1
6
11
5
10
15
Front view
5
10
15
1
6
11
In this case is VGA connector led on own cable out of device. Lenght of cable depends on stand hight
or following individual needs.