ELCOM Uniq 150, Service Manual, Page: 18 / 41

28
Elcom, spoločnosť s ručením obmedzeným, Prešov Elcom, spoločnosť s ručením obmedzeným, Prešov
29
Uniq 150 Service manual Service manual Uniq 150
2.11. RF reader installation
1. Cut red marked area of components before installation.
2. Skip two particular screws at the installation of bottom strip.
3. Also skip two particular screws at the rear and top cover closing.
4. Adjust lenght of USB cable to approximately 200 mm and move it through cutting in side profile. Cable type
depends to type of free USB connector on mainboard.* Solder cable to reader. It can happen, that the piece
which is installation executed on, already consists cabel with free wires.
Note: It is not possible to move cable through hole in side profile after soldering.
5. Stick reader on bottom box cover with two layers of doublesided thick sticker tape to provide bigger gap
between module and bottom box cover.
6. Put upper box cover on bottom cover.
7. Connect USB cable to free USB connector on mainboard.
8. Fix reader holder to the Uniq 150 after closing Uniq 150 covers and installation side profile.
9. Bond reader to the holder with doublesided sticker tape.
Reader cable must be tucked completly inside!
Figure 2.11. – RF reader installation
Alternatives of RF reader interconnection
Box PS17 × 35 × 65 KM57 bottom cover
Doublesided thick tape 9 × 20 mm
USB RFID reader ID12
Box PS17 × 35 × 65 KM57 top cover
RFID holder Doublesided tape Tesafix 4965 9 × 55 mm
Screw M2,5 × 8 DIN965 kužeľová
cca 150
ø2,5
ø4
Start side profile stick at the cutting
in case of RFID module installation.
Side profile adjustment
4
72
Bottom strip adjustment
ø4
94
Rear cover adjustment
1
12
34
shielding
4
3
2
1
4
3
2
1
1
2
3
4
Needed to order Quantity Ord. code
Doublesided tape Tesafix 4965 9 × 55 mm 2 M990089
RFID holder 1 M051087
Box PS17 × 35 × 65 KM57 bottom cover
1 M040580
Box PS17 × 35 × 65 KM57 top cover
USB RFID reader ID12
1 M310020
Doublesided thick tape 9 × 20 mm 6 M990050
Screw M2,5 × 8 DIN965 conical 4 M250215
USB extension cord AF, AM 1m
Cable 8-wires 250 mm 28 AWG 2H
1 *
M200141
M200143
2.12. Barcode reader installation
1. Drill holes to rear cover for screws before installation.
2. Fix reader to holder.
3. Fix holder to rear cover. We recommend spread a bit of fixation sealant thread to ensure against loosening nuts.
4. Reader cable connect to one of external USB ports in leg or tube.
Figure 2.12. – Barcode reader installation
Screw M3 × 6 DIN965 conical
Barcode reader holder
Screw M3 × 10 DIN965 conical
Barcode reader MS-1207FZY-1000R
Nut M3 DIN934
Serrated lock washer M3 DIN6798
Needed to order Quantity Ord. code
Screw M3 × 6 DIN965 conical 3 M250175
Sealant PERMABOND HM129 PP M060146
Nut M3 DIN934 4 M250030
Barcode reader holder 1 M051090
Screw M3 × 10 DIN965 conical 4 M250217