background image

2019-3938 
2019-11-06 

 

LABEL – CONTROLLER/CELL 

 

ECO-matic MEMS36USA Automatic 

 

CHLORINE GENERATOR 

DEVICE 

 

CONTROLS BACTERIA AND ALGAE 

In 

Swimming Pool (Spa) Waters 

COMMERCIAL 

A maximum of 50,000 L of water can be treated with one ECO-matic MEMS36USA 

Automatic Chlorine Generator unit. 

 

Maximum output of hypochlorous acid of 0.85 kg of free available chlorine per day in ideal conditions. However, an 

output of hypochlorous acid of 0.41 kg/day is more representative of typical conditions 

 

For swimming pools, a range of 1-3 ppm of free available chlorine must be maintained. 

For spas, a range of 3-5 ppm of free available chlorine must be maintained. 

 

READ THE LABEL AND OPERATING MANUAL BEFORE USING 

KEEP OUT OF REACH OF CHILDREN 

REGISTRATION NO. 30295 

PEST CONTROL PRODUCTS ACT 

 

WARNING: operating the unit without water flow through the cell can cause a build up of flammable gases which can 

result in FIRE OR EXPLOSION. 

 

Do not use this device with bromide products 

 

NOTICE TO USER: This pest control product is to be used only in accordance with the directions on the label. It is an 

offence under the Pest Control Products Act to use this product in a way that is inconsistent with the directions on the 

label.  

 

Davey Water Products Pty. Ltd 

6 Lakeview Drive 

Scoresby, Victoria 3179 

Australia 61 397 309 232 

 

IN CANADA, CONTACT: 

Alpine Spa Covers 

2103 – 43

rd

 St 

Vernon, BC V1T 6K7 

1-800-667-9707 

 

Summary of Contents for MEMS36USA
































Reviews: