ECO-MATIC MEMS36USA Installation & Operation Instructions Download Page 2

Page: 2 / 31

LABEL – CONTROLLER/CELL

Replacement cell for ECO-matic MEMS36USA Automatic Chlorine Generator

or ECO-matic MEMS16USA Automatic Chlorine Generator

Replacement cell for the chlorine generating device ECO-matic MEMS36USA Automatic

Chlorine Generator REGISTRATION NUMBER 30295 or ECO-matic MEMS16USA Automatic Chlorine Generator

REGISTRATION NUMBER 30299

PEST CONTROL PRODUCTS ACT

This cell must only be used on this model of chlorine generating device.

Do not use this device with bromide products

Read the Label, the Installation Manual and Operation Manual of the chlorine generating device ECO-matic

MEMS36USA Automatic Chlorine Generator or ECO-matic MEMS16USA Automatic Chlorine Generator

Davey Water Products Pty. Ltd

6 Lakeview Drive

Scoresby, Victoria 3179

Australia 61 397 309 232

IN CANADA, CONTACT:

Alpine Spa Covers

2103 – 43

Vernon, BC V1T 6K7 1-800-667-9707

Summary of Contents for MEMS36USA
































Search results

Summary of Contents for MEMS36USA

Reviews:

Related manuals for MEMS36USA

Brands by name

Popular brands

ECO-MATIC MEMS36USA, Installation & Operation Instructions

Search results

Summary of Contents for MEMS36USA

Reviews:

Related manuals for MEMS36USA

Brands by name

Popular brands