ECKELMANN Virtus 5 Series Operating Instructions Manual Download Page 134

Page: 134 / 183

Firmware V7.16.x

16.05.2023

134/183

Interface Ethernet

The Ethernet interface for the connection in a LAN is configured in this screen. This interface is used for the

data exchange and communication with LDSWin.

The screen contains the following parameters:

Interface - Ethernet

Input

Default

MAC address

Display of the MAC address

Device-dependent

Host name

Input of the host name

Text

ci4000

Obtain IP address via DHCP

Set checkmark that the IP settings are
obtained via DHCP

Checkmark

IP address

Input of the IP address

Numbers

10.0.28.66

Subnet mask

Input of the subnet mask

Numbers

255.255.255.0

Default gateway

Input of the default gateway

Numbers

10.0.28.1

Preferred DNS server

Input of the preferred DNS server

Numbers

Alternative DNS server

Input of the alternative DNS server

Numbers

Interface USB

An update (e.g. for update of the firmware and/or boot loader) can be performed using a USB stick

via the USB host port (left USB female connector, type A); for further details, see chapter

Firmware Update

Using the USB slave port (right USB female connector, type B), this interface can be configured to be able to
access the system with LDSWin or

Virtus Contol Desk

USB

Input

Default

IP address

Input of the IP address

Numbers

169.254.2.1

Subnet mask

Input of the subnet mask

Numbers

255.255.0.0

IP ports

The TCP/IP ports of the services can be configured in this screen.

Service

Input

Default

LAN gateway

Input of the TCP/IP port for the LAN gateway

Numbers (1 ...65535)

5000

VNC server

Input of the TCP/IP port for the VNC server; for
details see chapter

Remote control of the system

centre via VNC (Virtual Network Computing)

Tick the check box "Allow VNC": remote access via

VNC is possible (factory setting).

Numbers (1 ...65535)

5900

An Ethernet crossover patch cable CAT5 is needed for a local connection between system centre and
PC (LDSWin as remote station)!



An error message is output if the changed values are not applied when saving!
Then the values actually used by the system centre are displayed again on the entry screen.



Summary of Contents for Virtus 5 Series
























































































































































































Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands

ECKELMANN Virtus 5 Series, Operating Instructions Manual

Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands