ECKELMANN Virtus 5 Series Operating Instructions Manual Download Page 56

Page: 56 / 183

Firmware V7.16.x

16.05.2023

56/183

6.1.2 Handling wide COMBICON connector

Correct handling

Mating connectors

must

be plugged or

unplugged vertically and without canting

Incorrect handling

DANGER

Warning of dangerous electrical voltage! Danger to life - Danger of electric shock!

For assembly,

the safety regulations and the work safety instructions

must be

observed.

All

plug-in connections may

only be plugged and unplugged in a de-energised state.



For detailed information on handling wide COMBICON connectors, see

online in EDP



ATTENTION

Incorrect handling leads to damage to the plug socket! Never

detach the mating connector on one

side, as this will damage the pins of the plug socket!



Summary of Contents for Virtus 5 Series
























































































































































































Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands

ECKELMANN Virtus 5 Series, Operating Instructions Manual

Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands