ECKELMANN Virtus 5 Series Operating Instructions Manual Download Page 74

Page: 74 / 183

Firmware V7.16.x

16.05.2023

74/183

•

2. File upload of the firmware

Requirements for performing the firmware update

- Access to the

Virtus Control Desk

of the system centre, e.g. via LAN connection or via USB slave, see

chapter

Configuration of the E*LDS system using Service PC on site.

- Current firmware on the computer at

https://edp.eckelmann.de/edp/lds/_qdCE7mLLnp

Execution of the firmware update

locally on site

for details, see chapter

Remote control via Virtus Control Desk

in the Firmware section.

3. Locally on site using a USB stick

Requirements for performing the firmware update:

The new firmware must be available; this is usually provided as a compressed ZIP archive, e.g. at

https://

edp.eckelmann.de/edp/lds/_qdCE7mLLnp

The ZIP archive (it contains the directory "

CI4000

") must be unpacked using a PC into the root directory of a

USB stick (1 GB .. <=16 GB with 1 GB free space)
The USB stick for the firmware update and the configuration data

must be formatted with FAT32

as file

system!
The requirements are met if the unpacking and copying to the USB stick has taken has taken place as
follows:
The directory, e.g.

F:\CI4000

exists on the USB stick (if "F" is the drive letter for the plugged-in USB stick).

Execution of the firmware update

locally on-site:

For details, see chapter

Menu 4-1-9 - Firmware Update

Practical tip

After performing the firmware update, check whether the desired firmware version has been
successfully installed (menu 4-1-9 or

Info field in the main menu



Summary of Contents for Virtus 5 Series
























































































































































































Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands

ECKELMANN Virtus 5 Series, Operating Instructions Manual

Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands