ECKELMANN Virtus 5 Series Operating Instructions Manual Download Page 162

Page: 162 / 183

Firmware V7.16.x

16.05.2023

162/183

9.2.1 Remote control via Virtus Control Desk (VCD)

The system centre can be remotely controlled using a web browser, e.g. Firefox (

http://www.firefox.com/

) using

the integrated Virtus Control Desk; for details see chapter

Configuration of the E*LDS system using Service PC

on site

After starting the browser, the IP address of the system centre (

Menu 4-1-5 - Interfaces

) must be entered in the

address field of the browser.

The Virtus Control Desk includes the following parameters:

Language settings

DE/EN

The language in Virtus Control Desk can be changed using the DE/EN buttons.

Logout

Tap on the button

to disconnect the connection to the Virtus Control Desk.

Tab "Components"

Firmware
Update

Summary of Contents for Virtus 5 Series
























































































































































































Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands

ECKELMANN Virtus 5 Series, Operating Instructions Manual

Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands