ECKELMANN Virtus 5 Series Operating Instructions Manual Download Page 165

Page: 165 / 183

Firmware V7.16.x

16.05.2023

165/183

9.2.2 Remote operation of the system centre using VNC (Virtual Network Computing)

The system centre can be remotely operated using VNC with, for example, the

). After starting the VNC viewer, the IP address of the system centre must be entered in the

"VNC Server" configuration field. The connection is then established by clicking with the mouse on the
"Connect" button.

Example 1:

Establishment of a VNC connection to the system centre with the IP address

10.0.28.27

If the VNC port has been changed (see Menu 4-1-5, page 105), the new port must be explicitly appended with
a colon after the IP address.

Summary of Contents for Virtus 5 Series
























































































































































































Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands

ECKELMANN Virtus 5 Series, Operating Instructions Manual

Search results

Summary of Contents for Virtus 5 Series

Reviews:

Related manuals for Virtus 5 Series

Brands by name

Popular brands