background image

LX20G_Manual_en_v2.1 

Page 19 / 

69 

 

 Serial port where GSM modem is connected (e.g. Wavecom Fastrack) 

 PIN code of SIM card installed in GSM modem e.g. 1111 

  Serial  port  parameters:  amount  of  bytes/sec.  (e.g.  115200),  data  bytes  (8), 

parity  (none), stop bytes (1)     

 

 

 
 

Click  [Add]  button  to  confirm  settings  and  save  connection  (settings  are  inserted 

into  table).  Since  that  time  a  remote  connection  to  device,  reading  and  saving  of 

parameters in LX20G memory is possible.  
 

Note 

:  Remote  configuration  with  CSD  canal  is  possible  if  option  of  CSD  data 

sending has been activated both for SIM card inserted into a device and  SIM card 

installed  in  GSM  modem.  Beside,  LX20G  transmitter  must  enable  to  pick  up  data 

calls (see GSM modems authorized phones) 

 

Programming  with  CSD  is  also  possible  if  OSM.Server  system  has  been  installed, 
and  minimum  one  GSM  modem  is  connected.  If  device  has  been  entered  onto 

server  list  (factory  number  and  SIM  card  telephone  number  –See  OSM.Server 

Operation  Manual)  it  is  possible  to  use  link  via  OSM.  It  is  possible  if  device  is  not 
connected to the OSM.Server via GPRS. During programming procedure (with GPRS 

link-  See  above)  a  question  will  be  displayed  if  user  want  to  use  a  modem 
connected to the server. After confirmation procedure will follow as in case of other 

programming channels.  
 

6.3.6.

 

File -> Automatic device settings backup 

 
All configuration settings including reread from devices and saved on devices are to 

be  automatically  saved  on  hard  disc.  If  during  installation  on  configuring  tool 
settings have not been changed, files will be saved as follows: 

C:\Program Files\ EBS\KonfiguratorLX\configs\LX20G _20000 

Catalog LX20G_20000 contains all files in respect of LX20G with factory number of 
20000  programming.  The name contains date and time of operation and its type 

(saving/ reading). Files have 

cmi

 extension.   

 

6.3.7.

 

File -> Exit

 

 
Finishes program operation. 

 

Summary of Contents for LX20G






































































Reviews: