EBS LX20G Installation And Programming Manual Download Page 66

Page: 66 / 69

LX20G_Manual_en_v2.1

Page 66 /

10.

LED DIODES INDICATION

LED diodes (4), mounted directly on printed circuit, are purposed to show current
condition of the device.

10.1.

LOGGING TO GSM NETWORK

Once SIM card has been inserted into the device and power supply was turned on
logging to GSM system follows.

Description

LED Diodes

Green (A)

Red

Logging to GSM

10.2.

GSM RANGE

Flickering of a green diode indicates GSM signal (1-8 flickers).

Device operation mode is signalled with a green diode on during 2 seconds once the
range was detected. If after signalling range diode will not flash for 2 seconds the

device is in SMS mode. Range indication is interrupted during data transmission,
and after sending of data again GSM range is being indicated.

Description

LED Diodes

Green (A)

Red (D)

GSM range = 8
GPRS mode

GSM range = 6
SMS mode

Summary of Contents for LX20G






































































Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands

EBS LX20G, Installation And Programming Manual

Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands