EBS LX20G Installation And Programming Manual Download | Manualshive

Page: 26 / 69

background image

LX20G_Manual_en_v2.1

Page 26 /

69

7.1.5.2.

Installer code

Allows restricted access to the parameters of device. When installer code is used

following groups of parameters are unavailable: Access, Transmission, Restrictions,
SMS notifications, Link control, RS232, Phone line and Dialer. Choosing

unauthorized groups of parameters in “GPRS transmitter configurator” causes error
notification.

Default installer code:

2222

7.1.5.3.

PIN of SIM card

As a device operates via GSM network, SIM card is indispensable and it may be

received from phone operator. Before the first use PIN code of SIM card shall be
programmed for operation in given transmitter. PIN code is indispensable for

automatic system launching. In case of card without PIN code, it is possible to enter

any value e.g. 0000.
If you enter wrong PIN number after inserting card and switching on transmitter,

the system will not launch and you may be able to use card after entering PUK card
only (with use of any GSM mobile phone).

Factory setting of PIN in LX20G transmitter is

1111

.

7.2.

TRANSMISSION

For the purpose of maximum security of transmission, data is encrypted with AES
key. This option may be used for GPRS and SMS transmission.

After selection of encrypted transmission you may use your own code (256 bytes –
signs 0-9 and A-F) or use default settings.

Selection of not coded transmission means device operation similar to PX

transmitters.

«
...
24
25
26
27
28
...
»

Summary of Contents for LX20G






































































Reviews:

No comments

Related manuals for LX20G

RFX-RMT-II Dual Band SD/HD

Brand: RF Central Pages: 38

Brand: Dolphin Pages: 17

vigilantplant YTA70

Brand: YOKOGAWA Pages: 5

Brand: Alinco Pages: 37

Brand: HESCH Pages: 16

Brand: BNF Pages: 45

Brand: JRC Pages: 44

Brand: Yaesu Pages: 45

Brand: Continental Automotive Pages: 8

Brand: DTC Pages: 123

Brand: Airline Pages: 37

ALPHA CON 190 18 DIN CONDUCTIVITY CONTROLLERTRANSMITTER

Brand: EUTECH INSTRUMENTS Pages: 39

FT DX 9000MP CONTEST - DATA MANAGEMENT OPERATION

Brand: Yaesu Pages: 180

Brand: Leviton Pages: 2

Brand: Contact Pages: 16

Brand: ChatterBox Pages: 9

Brand: Minebea Pages: 34

Brand: TEM Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands