EBS LX20G Installation And Programming Manual Download

Page: 48 / 69

LX20G_Manual_en_v2.1

Page 48 /

7.9.1.

Phone line

This tab is provided to determine settings of telephone line.

7.9.1.1.

Line connected to the control panel…

This feature allows you to select the default connection for the control panel.

After selecting:

PSTN – terminals T1-R1 are connected to PSTN line, terminals T2-R2 are not

connected

GSM – terminals T1-R1 are connected to GSM line, terminals T2-R2 are

connected to PSTN line

7.9.1.2.

Routes of the transmission for the control panel

The user is able to determine which lines and what order will be used for

subsequent failed call attempts to the monitoring station. Using the drop-down lists
specify the order of routes of transmission: PSTN, GSM and GPRS / SMS. The

algorithm works as follows:

When lifting the handset by the control panel transmission route is determined

by the following criteria:

If prefix code was used (see

7.9.2.1 Forcing the line

) the route is

chosen to be a line which is assigned to the given code.

If prefix code was not used the line is chosen by the user-defined
sequence for which no failure occurred. For PSTN and GSM see

7.9.1.3

Summary of Contents for LX20G






































































Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands

EBS LX20G, Installation And Programming Manual

Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands