EBS LX20G Installation And Programming Manual Download Page 61

Page: 61 / 69

LX20G_Manual_en_v2.1

Page 61 /

DEVICE PROGRAMMING

Programming of device is possible with “GPRS transmitters configurator”

configuration program described in chapter 5. To program the device establish

connection with a device.
Depending on connection mode there are two ways for programming.

8.1.

LOCAL PROGRAMING

To program a device locally follow the procedure:

Connect PROG joint (on printed circuit) with COM computer port by way of

service wire, defined in option -> RS-232.

Connect power supply to terminals

+12V

and

GND

. After connection and

detection of programming wire a module shall signal this with LED diodes: a

green one shall flash and red one shall flicker.

Launch software and define device options (description is in chapter 6 of this

Manual ). Provide right PIN code for SIM card.

Save settings into memory of device. Saving course is displayed in special

window.

After saving disconnect power supply and disassembly service wire.

Insert SIM card. Connect module wiring pursuant to guidelines from chapter

4. Turn power supply on.

The device is ready to transmit data.

8.2.

REMOTE PROGRAMMING

Remote programming of device is possible if:



user uses GPRS transmitters configurator and GSM modem connected to PC



user uses OSM.Server monitoring system receiver.

In first case remote programming is possible on CSD channel and its procedure is
analogous to local programming, remembering that “Modem GSM” shall be selected

from connection options (See chapter 6.3.5.2-CSD Link).

Note

: Remote configuration with use of CSD canal is possible only if transmission of

CSD data is active both for SIM card inserted in the device, and for SIM card
installed in GSM modem.

Summary of Contents for LX20G






































































Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands

EBS LX20G, Installation And Programming Manual

Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands