EBS LX20G Installation And Programming Manual Download

Page: 57 / 69

LX20G_Manual_en_v2.1

Page 57 /

7.11.

FIRMWARE

The device is equipped with built in bootloader that allow for updating and change of
firmware. During programming all information is displayed in respect of carried out

operation.

Follow the following procedure:

Launch configuration program

Open “Firmware” option of configuration wizard

Open file with new firmware (click [Open] button to locate where file is).

Select file transmission mode: local or remote.

Note: Procedure of assigning firmware to a device is analogous to
programming a device. For procedure refer to chapter 8 Programming of

the device.

Click [Start] button to start software exchange.

Loading course is displayed on special window.

Close the window after completed saving

From this time on the device will work under control of new firmware.

Note : The above procedure shall be carry out with due care to avoid

improper device operation

Summary of Contents for LX20G






































































Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands

EBS LX20G, Installation And Programming Manual

Search results

Summary of Contents for LX20G

Reviews:

Related manuals for LX20G

Brands by name

Popular brands