Eaton Power Xpert XGIS Instruction Booklet Download Page 6

Page: 6 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Read and understand these instructions before attempting

installation, operation, or maintenance of this equipment. This

equipment must be installed and serviced only by qualified electrical

personnel. Retain this document for future use.

WARNING

IMPROPERLY INSTALLING OR MAINTAINING THESE PRODUCTS CAN

RESULT IN DEATH, SERIOUS PERSONAL INJURY, OR PROPERTY DAMAGE.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE ATTEMPTING

ANY UNPACKING, ASSEMBLY, OPERATION OR MAINTENANCE OF THE

CIRCUIT BREAKERS.

INSTALLATION OR MAINTENANCE SHOULD BE ATTEMPTED ONLY

BY QUALIFIED PERSONNEL. THIS INSTRUCTION BOOK SHOULD NOT

BE CONSIDERED ALL INCLUSIVE REGARDING INSTALLATION OR

MAINTENANCE PROCEDURES. IF FURTHER INFORMATION IS REQUIRED,

YOU SHOULD CONTACT EATON.

WARNING

DO NOT ATTEMPT ANY WORK ON THIS EQUIPMENT SUCH AS INSTALLING

COMPONENTS, PERFORMING ANY EXAMINATIONS, PERFORMING ANY

ADJUSTMENTS, PERFORMING ANY SERVICING, OR PERFORMING ANY

MAINTENANCE WHILE IT IS ENERGIZED. BEFORE PERFORMING ANY

WORK, FOLLOW ALL APPROPRIATE HAZARD ASSESSMENT AND ENERGY

CONTROL PRECAUTIONS AND PROCEDURES.

VERIFY NO VOLTAGES ARE PRESENT ON ALL INCOMING AND OUTGOING

CONDUCTORS, AND ANY ENERGY SOURCES CONTAINED WITHIN THE

EQUIPMENT PRIOR TO SERVICING, THEN GROUND (CONNECT TO EARTH)

ALL INCOMING AND OUTGOING CONDUCTORS ATTACHED TO THIS

EQUIPMENT AND TO ANY INTERNAL ENERGY SOURCES.

All possible contingencies which may arise during installation,

operation or maintenance, and all details and variations of this

equipment do not purport to be covered by these instructions. If

further information is desired by purchaser regarding his particular

installation, operation or maintenance of particular equipment,

contact an Eaton representative.

Summary of Contents for Power Xpert XGIS

















































































Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands

Eaton Power Xpert XGIS, Instruction Booklet

Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands