Eaton Power Xpert XGIS Instruction Booklet Download Page 49

Page: 49 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Main bus compartment vertical joins
Attach using 5 sets of M10-1.5 x 30 lg SHCS, M10 wide flat

washer, M10 split lock washer, M10 nut.

Figure 78. Main bus compartment vertical joints.

Main bus compartment horizontal splice plate (see

Figure 75

item 6).
Attach to studs on the top of the tank in each section using 10

sets of M8 wide washer, M8 split lock washer, M8 nut.

Figure 79. Main bus compartment splice plate.

Upper VT/relief compartment horizontal splice plate (see

Figure 75

, item 7)

Attach the front portion (ahead of the notch) holes to tank

studs using 2 sets of M8 wide washer, M8 split lock washer,

M8 nut.
Attach two holes (behind the notch) to one tank stud on each

tank using 2 sets of M8 wide washer, M8 split lock washer,

M8 nut.
Attach the remaining two sets of two holes using through

hardware: Qty 4 sets of M8-1.25 lg SHCS, M8 wide washer,

M8 split lock washer, M8 nut.

Figure 80. Upper VT/relief compartment splice plate.

Vertical section rear edge bolts (see

Figure 75

, item 8)

Attach using 17 sets of M10-1.5 x 30 lg SHCS, M10 wide flat

washer, M10 split lock washer, and M10 nut.

Section exterior fastenings
Rear vertical splice plate (elbow) (see

Figure 75

, item 9)

Attach the horizontal part using 4 sets of M8-1.25 x 25 lg

SHCS, M8 wide washer, M8 split lock washer, M8 nut.
Attach the vertical part using 12 sets of M8-1.25 x 25 lg SHCS,

M8 wide washer, M8 split lock washer, M8 nut.

Figure 81. Rear vertical splice plate.

Summary of Contents for Power Xpert XGIS

















































































Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands

Eaton Power Xpert XGIS, Instruction Booklet

Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands