Eaton Power Xpert XGIS Instruction Booklet Download Page 15

Page: 15 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Figure 14. 3PDS manual operation T-handle.

NOTICE

DURING MANUAL OPERATION, THE THREE POSITION DISCONNECT

SWITCH HAS NO SCREW DRIVE TRAVEL MECHANICAL LIMITS. IT CAN

BE MOVED INTO OVERTRAVEL POSITIONS AT BOTH ENDS OF TRAVEL

(GROUND AND CLOSED).

DO NOT MOVE THE SCREW DRIVE BEYOND ITS END OF TRAVEL

INDICATIONS, AS THAT CAN RESULT IN DAMAGE TO THE SCREW DRIVE

MECHANISM. USE THE THREE POSITION DISCONNECT SWITCH STATUS

DISPLAY WINDOWS TO DETERMINE WHEN THE THREE POSITION

DISCONNECT SWITCH HAS REACHED THE DESIRED LOCATION.

Figure 15. Disconnect switch windows and label.

In order to ground the output cables or coupling bus, the 3PDS must

be put in the ground position and the circuit breaker must be closed.
The 3PDS screw drive also propels a cam limit switch mounted

inside the operating mechanism. This cam limit switch has four

contacts. The contacts are used in the electric control system to

signal 3PDS status: closed, opened and grounded.
The 3PDS and circuit breaker are mechanically and electrically

interlocked to prevent inappropriate operation.

Figure 16. 3PDS chain drive.

A mechanical display provided on front of the 3PDS operating

mechanism face plate indicates the switch position status as shown

Figure 17.

Figure 17. 3PDS (normal operation).

Summary of Contents for Power Xpert XGIS

















































































Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands

Eaton Power Xpert XGIS, Instruction Booklet

Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands