Eaton Power Xpert XGIS Instruction Booklet Download Page 35

Page: 35 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Figure 64.

Coupling

Connector

Note:

The Output Compartment

can accommodate up to

three connectors, or two

connectors and a surge

arrester.

XGIS

Tank Wall

Cable Bushing

Output Bushing

Bracket

Coupling

Connector

Cap

Space

for

Cable CT

Tee

Connector

Surge Arrester

Separable power cable connectors.

Figure 65. Cable separable connectors in 2000 A or 2500 A

cable compartments.

The separable connectors include a shield layer that is used to

ground the exterior of the connectors. The ground wires must be

fastened to the compartment ground bus. This will ensure the outer

surface of the separable connectors are at ground potential.

Summary of Contents for Power Xpert XGIS

















































































Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands

Eaton Power Xpert XGIS, Instruction Booklet

Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands